General discussion • Re: Pi5 8GB vs 16GB - Geekbench 6
Do you have the same results?Sorry, no idea. I found it intriguing though and found this Geekbench comparison for RPI 5 with a wide discrepancy on reported results...
View ArticleClik here to view.
Raspberry Pi OS • labwc keybindings?
In X11 (vd. /etc/xdg/openbox/lxde-pi-rc.xml), Alt+F2 was mapped to execute lxpanelctl run. Is an equivalent action available in labwc?Also, after checking out the sample labwc rc.xml, I've tried...
View ArticleSDK • Re: I2C random timeouts using i2c_write_timeout_us()
A couple of notes bearing in mind that while I've researched this and implemented only the SMbus Alert Response Command using the Pico SDK, I am really a beginner at this.It is worth noting that while...
View ArticleGeneral • Re: Use debug probe with PICO 2
I was able to down load, compilem and install openocd supporting RP2350.Here are the steps.First you need the cmsis-dap driver.I had to modify the file config.ac and comment line 23/Code:...
View ArticleCompute Module • Re: CM5 trouble with 7inch display on DSI
New cables finally arrived today. Pinouts are actually different. One pin that should be a ground is floating, and some grounds have no continuity to other grounds.Sincerely thanks for the help to...
View ArticleInterfacing (DSI, CSI, I2C, etc.) • Re: Small TFT based on ILI9341 ST7789 -...
I swapped miso with mosi..... now it works, thanks! What about touch? How can I make it work?Statistics: Posted by tomek_yeet — Sat Jan 11, 2025 11:16 pm
View ArticleSDK • Re: Run fails in Pico Extension on Windows, need Zadig?
For Linux that's usually setting up rules in udev for Picotool. The github has them, just copy:Code: sudo cp udev/99-picotool.rules...
View ArticleRaspberry Pi OS • Re: systemd-timesyncd fails sync time for minutes after...
Thanks for responding bls!The problem I describe, where timesyncd doesn't appear to send an NTP request for more than 10 minutes, happens consistently after a few reboots. (I only noticed this because...
View ArticleMicroPython • Re: Unable to allocate memory on a raspberry pico w
My situation is quite specific, unfortunately I have to use a certain version of uPython that's about 5 years old My understanding of the MicroPython Release Notes is that the 'rp2' port did not get...
View ArticleTroubleshooting • Wire ethernet not working on new PI 5 Bookworm installs
new build not connecting with eth0 interface. works with wifi but would like bith to be configured and wired preferred when both are available.What am I doing wrong?Code: wkeeling@pi5dev8g:/etc $...
View ArticleBeginners • Can I connect to my laptop screen to see the Pi's console output?
Folks.....Yes, I know how to connect my Pi's to VNC and view the GUI on my computer. This is not my question!I have a number of head-less Pi's and it would be convenient to be able to connect a Pi to...
View ArticleBeginners • Re: Can I connect to my laptop screen to see the Pi's console...
You could configure your Pis to expose a serial console on the UART pins, then get a 3.3V USB serial adapter for your laptop. Plug the adapter into the laptop, and the serial pins into the GPIO. Run a...
View ArticleTroubleshooting • Re: Wire ethernet not working on new PI 5 Bookworm installs
Have you tried a known good Ethernet cable in a known working Ethernet port in your router?Have you tried rebooting the router?Statistics: Posted by neilgl — Sun Jan 12, 2025 10:45 pm
View ArticleAdvanced users • Re: No video output after POE+ssd HAT
Are you running the latest EEPROM software??> sudo rpi-updateCheck https://github.com/raspberrypi/rpi-upda ... /README.md for details.Statistics: Posted by mwallis — Sun Jan 12, 2025 11:07 pm
View ArticleAutomation, sensing and robotics • Re: Leviton D215S Control
Not exactly the solution you are looking for, but using MQTT enabled switches could be a solution.- Switch your load with a power plug https://www.shelly.com/de/products/shelly-plug-s-gen3 or...
View ArticleClik here to view.
General • Re: Problem with IRLZ44n mosfet in a circuit
So the 9V battery is struggling a bit at 7.4V, and about 6V across the 10 ohm, so 0.6A. 1.4V across the power FET and 0.6A, gives us about 2.3 ohm. But according to the IRLZ44N datasheet, with the...
View ArticleTroubleshooting • RaspberryPi and HyperpixelSq
My device and screen have been working well for maybe a year now. All of a sudden recently, the cursor is topsy turvy relative to the touch input. I was able to fix that, but now the VNC input is all...
View ArticleTroubleshooting • Re: Pi 5 8GB running Bookworm, WiFi is super slow ONLY IN...
ThanksI've used "menu -> preferences -> raspberry pi configuration" and now the country has changed in sudo iw reg get - I'll try to do more tests to see if that fixes the speed issueStatistics:...
View ArticleMicroPython • Re: Can't install Micropython on Thonny for Pico 2 - Noob here
Thanks guys. That is brilliant. So now my Raspberry Pi microcontroller adventure can begin. I was about to give up and stick to Arduino.Statistics: Posted by PhilipCr416 — Mon Jan 13, 2025 12:26 am
View ArticleClik here to view.
Beginners • Re: Is there any remote connection like RDP ?
Hi On the raspberry OS, is there a feature to connect to the graphical session, like RDP for Windows ?Something more "built in" than Anydesk.I want to connect to the session of a Pi who is in the...
View Article