Troubleshooting • Geekworm NASPi V2.0 Wont Boot

I'm hoping someone can help here. I tried to read around here and couldn't find a solution... I have an already setup raspi 4b which boots from ssd. There is no sd card. I have both an official power supply from raspi and a geekworm capable of 5A and 4A at more than 20W.

When I tried to install it into this case and get it running, it kept looping from usb to sd trying to boot but was never able to. Here is the error screen, as best as I could grab it. I ended up typing all of this out so if there are typos, its mine.

Raspberry Pi 4 Model B - 8GB
bootloader: 69471177 2025/05/08
update-ts: 1755048332

board: rev d03115 0014 serial 4cf0723 d2:d8:72:u3:82:10
boot: mode USB-MSD 4 order f14 retry 0/128 restart 28/-1
SD: card not detected
part: 1 mbr [0x0c:00004000 0x83:00104000 0x00:0000000 0x00:0000000]
fw: start.elf fixup.dat
net: down ip: 0.0.0.0 sn: 0.0.0.0 gw: 0.0.0.0
tftp: 0.0.0.0 00:00:00:00:00:00
display DISP0: HDMI HDP=1 EDID: ok #2 DISP1: HPD=0 EDID=none #0

MSD [02:00] 3.00 000000:03 LUN 0
MSD READ_CAPACITY [02:00] 3.00 00000:03 lun 0 block-count 250006982948
Trying partition: 0
type: 32 lba: 16384 'mkfs.fat' ' bootfs ' clusters 261116 (4)
Trying partition: 1
type: 32 lba: 16384 'mkfs.fat' ' bootfs ' clusters 261115 (4)
Read config.txt bytes 1247 hnd 0x252
xHC-CMD err: 13 type: 1 [02:00] 3.00 00000:03
FAT read failed @ 123896
Block device timeout
Boot mode: SD (01) order f
Failed to open device: 'sdcard' (cmd 371a0010 status 1fff0001)
Failed to open device: 'sdcard' (cmd 371a0010 status 1fff0001)
Boot mode: RESTART (0f) order 0
Boot mode: USB-MSD (04) order f1


Then the other screen:

Raspberry Pi 4 Model B - 8GB
bootloader: 69471177 2025/05/08
update-ts: 1755048332

board: rev d03115 0014 serial 4cf0723 d2:d8:72:u3:82:10
boot: mode SD 1 order f14 retry 1/1 restart 34/-1
SD: card not detected
part: 1 mbr [0x0c:00004000 0x83:00104000 0x00:0000000 0x00:0000000]
fw: start.elf fixup.dat
net: down ip: 0.0.0.0 sn: 0.0.0.0 gw: 0.0.0.0
tftp: 0.0.0.0 00:00:00:00:00:00
display DISP0: HDMI HDP=1 EDID: ok #2 DISP1: HPD=0 EDID=none #0

USB3[3] 00281203 connected enabled
USB3 root HUB port 3 init
MSD [02:00] 3.00 000000:03 register MSD
MSD [02:00] 3.00 000000:03 LUN 0
MSD READ_CAPACITY [02:00] 3.00 00000:03 lun 0 block-count 250006982948
Trying partition: 0
type: 32 lba: 16384 'mkfs.fat' ' bootfs ' clusters 261116 (4)
Trying partition: 1
type: 32 lba: 16384 'mkfs.fat' ' bootfs ' clusters 261115 (4)
Read config.txt bytes 1247 hnd 0x252
xHC-CMD err: 13 type: 1 [02:00] 3.00 00000:03
FAT read failed @ 123896
Block device timeout
Boot mode: SD (01) order f
Failed to open device: 'sdcard' (cmd 371a0010 status 1fff0001)


Any help...? I really like this case...

Statistics: Posted by Razash — Fri Jan 23, 2026 11:21 pm

---